alsr, alvr www.vishay.com vishay huntington revision: 18-feb-16 1 document number: 31800 for technical questions, contact: ww2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 wirewound resistors, commercial power, silicone coated, axial lead features ? high temperature coating (> 350 c) ? all welded construction ? available with vitre ous like appearance coating as alvr ? available in non-inductive styles with ayrton- perry winding for lowest reactive components, special ni ? material categorization: ? for definitions of compliance please see www.vishay.com/doc?99912 notes (1) vishay huntington alsr / alvr models have two power ratings de pending on operation temperature and stability requirements. mode ls not available for characteristic v ar e: alsr01, alvr01, alsr03, and alvr03. (2) other tolerances may be available, contact factory. standard electrical specifications global ? model historical model power rating (1) p 25 c w characteristic u +250 c power rating (1) p 25 c w characteristic v +350 c resistance range ? tolerance (2) % weight (typical) g alsr01 alsr-1 1 - 0.10 to 6.37k 1, 3, 5, 10 0.27 alvr01 alvr-1 1 - 0.10 to 6.37k 1, 3, 5, 10 0.27 alsr03 alsr-3 3 - 0.10 to 12k 1, 3, 5, 10 0.68 alvr03 alvr-3 3 - 0.10 to 12k 1, 3, 5, 10 0.68 alsr5a alsr-5a 4 5 0.10 to 40.3k 1, 3, 5, 10 2.1 alvr5a alvr-5a 4 5 0.10 to 40.3k 1, 3, 5, 10 2.1 alsr05 alsr-5 5 7 0.10 to 58.5k 1, 3, 5, 10 3.2 ALVR05 alvr-5 5 7 0.10 to 58.5k 1, 3, 5, 10 3.2 alsr10 alsr-10 7 10 0.10 to 92k 1, 3, 5, 10 4.9 alvr10 alvr-10 7 10 0.10 to 92k 1, 3, 5, 10 4.9 global part number information global part numbering example: alsr0325r00fe12ni global model (6 digits) value (5 digits) tolerance (1 digit) packaging (3 digits) special (up to 2 digits) (see standard electrical specifications global model column for options) r = decimal k = thousand 1r500 = 1.5 ? 1k500 = 1.5 k ? f = 1.0 % h = 3.0 % j = 5.0 % k = 10.0 % e07 = tape / reel (alsr5a / alvr5a, alsr05 / ALVR05) e08 = tape / reel (alsr01 / alvr01) e29 = tape / reel (alsr10 / alvr10) e48 = tape / reel (alsr03 / alvr03) e70 = tape / reel, 1k pieces (smaller than alsr05 / ALVR05) e73 = tape / reel, 500 pieces e12 = bulk, 100 pc boxes (dash number) from 1 to 99 as applicable ni = non-inductive historical part number example: alsr-3-25-1 %-ni alsr-3 25 ? 1 % ni historical model resistance value tolerance special lsr0325 r00fe 1 a 2 n i
alsr, alvr www.vishay.com vishay huntington revision: 18-feb-16 2 document number: 31800 for technical questions, contact: ww2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions in inches [millimeters] material specifications element: copper-nickel alloy or nickel-chrome alloy, depending on re sistance value core: ceramic: steatite or alumina, depending on physical size end caps: stainless steel coating: special high temperat ure silicone or special formula of vitreous like appearance coating on alvr terminals: tinned copper clad steel part marking: hei, model, value, tolerance, date code derating global model dimensions in inches [millimeters] l 0.032 [0.813] d 0.032 [0.813] ld 0.002 [0.051] alsr01 0.406 [10.31] 0.110 [2.79] 0.020 [0.508] alvr01 0.406 [10.31] 0.110 [2.79] 0.020 [0.508] alsr03 0.500 [12.70] 0.180 [4.57] 0.032 [0.813] alvr03 0.500 [12.70] 0.180 [4.57] 0.032 [0.813] alsr5a 0.920 [23.37] 0.200 [5.08] 0.032 [0.813] alvr5a 0.920 [23.37] 0.200 [5.08] 0.032 [0.813] alsr05 0.875 [22.23] 0.312 [7.92] 0.032 [0.813] ALVR05 0.875 [22.23] 0.312 [7.92] 0.032 [0.813] alsr10 1.730 [43.94] 0.312 [7.92] 0.032 [0.813] alvr10 1.730 [43.94] 0.312 [7.92] 0.032 [0.813] 1.50 [38.10] min. l d ld rated power in % ambient temperature in c 120 100 80 60 40 20 0 25 - 65 - 50 250 100 50 300 350 0 200 150 characteristic u characteristic v technical specifications parameter unit resistor characteristics temperature coeffici ent ppm/c 30 for 10 ? and above; 50 for 1 ? to 9.9 ? ; 90 for 0.5 ? to 0.99 ? terminal strength lb 10 minimum dielectric withstanding voltage v ac 500 for 1 w and 1000 for 3 w and above operating temperature range c cha racteristic u = -65 to +250, ch aracteristic v = -65 to +350 maximum working voltage v ( p x r ) 1/2 performance test conditions of test test limits (characteristic v) thermal shock rated power applied until thermally stable , then a minimum of 15 min at -55 c (2.0 % + 0.05 ? ) > ? r short time overload 5x rated power (3 w and smaller), 10x rated power (4 w and larger) for 5 s (2.0 % + 0.05 ? ) > ? r dielectric withstanding voltage 500 v rms , 1 min for 1 w and 1000 v rms , 1 min for 3 w and above (0.1 % + 0.05 ? ) > ? r low temperature storage -65 c for 24 h (2.0 % + 0.05 ? ) > ? r high temperature exposure 250 h at u = +250 c, v = +350 c (4.0 % + 0.05 ? ) > ? r mechanical shock mil-std-202 method 213, 100 g s for 6 ms, 10 shocks (0.2 % + 0.05 ? ) > ? r vibration frequency vari ed 10 hz to 2000 hz, 20 g peak, 2 directions 6 h each (0.2 % + 0.05 ? ) > ? r load life 2000 h at rated power, +25 c, 1. 5 h on, 0.5 h off (3.0 % + 0.05 ? ) > ? r moisture resistance mil-std-202 method 106, 7b not applicable (2.0 % + 0.05 ? ) > ? r
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
